HERSCHEDE BUSHING KIT BERGEON SWISS REAMERS

Herschede Bergeon bushing kit with SWISS made reamers consists of: one BA-5 System Brass KWM size bushing assortment (100 bushings, 10 sizes at 10 each) one HRB-1 Herschede Back Plate Winding Arbor Bushings (10 bushings) one HFR-1 Herschede Front Plate...

BERGEON BUSHING TOOL CENTER FRAME ONLY

Bergeon 6200 bushing tool center frame only. Not included is the chuck, handle, arms, or accessories (reamers, anvils, etc) Made in Switzerland.  WARNING: This product may contain lead and lead is on the California Proposition 65 list because...

PUSHERS - KWM GERMAN MADE

Genuine KWM precision pushers for American and KWM sized bushings. Use with the KWM bushing tool or hand tool.  Select size such that the pusher is slightly larger than the bushing outside diameter. Made in Germany by Flume (KWM).

BERGEON REAMERS FOR KWM - SWISS MADE

Reamers for Bergeon 6200 Bushing Tools or Bergeon handle (SKU: Bergeon-Handle). Genuine Bergeon Swiss made cutters fit American/KWM bushing sizes. Select from the different reamer sizes. Made in Switzerland.  WARNING: This product may contain lead...

KWM REAMERS - FLUME GERMAN MADE

High quality genuine KWM German hand reamers for American and KWM sized bushings. Select from reamer sizes ranging from 1.18mm to 8.64mm, a chamfering tool, centering points (standard or long), or a handle. Pieces sold individually.  A 5 piece KWM...

CENTER SHAFT ONLY FOR KWM TOOL - GERMAN MADE

An upright center shaft replacement from the factory for the KWM Bushing Tool Set.  The shaft tool accepts the KWM reamers, chamfering, and pusher tools.  The center shaft spindles are best suited for Flume KWM or Elma bushings machines after...

ANVILS WITH HOLE - KWM GERMAN MADE

Anvil I (No. 1), Anvil II (No. 2), Anvil III (No. 3), Anvil IV (No. 4), Anvil V (No. 5), and Anvil VI (No. 6) with hole for use with KWM, K&D, and Drill-A-Bush tools.  Blackened finish.  Select size. Pieces sold individually.  By Flume...

BERGEON BRONZE 10 PIECE BUSHINGS - SWISS MADE

Select the available Swiss Made Bergeon Bronze Bushing (BZS-part number) from the table below. Bushings are sold in packages of 10. Made in Switzerland.  

BERGEON BRASS 10 PIECE BUSHINGS - SWISS MADE

Select the available Swiss Made Bergeon Bushing (BBS-part number) from the table below. Bushings are sold in packages of 10.

HANDLE FOR BERGEON REAMERS

Handle for use with genuine Bergeon reamers.  Knurled handle is made of steel and comes with hex wrench for tightening reamers.  Handle: 4 1/2" L. Purchase individual Bergeon reamers (SKU's: 6200) and place in the hand tool to ream your...

BUSHING FOR STRIKE

Bushing for strike winding arbor.  Size:  .330" OD x .190 ID x .25" diameter.

MAIN WHEEL BLANK BUSHINGS

Herschede and many other makers main wheel arbors, pulleys, barrels, barrel caps and numerous other precision mechincal applications.  Great for key winding arbors for mantel, floor, or wall clocks.  May be used on center wheel.  Drill may...

ANVILS WITH HOLE - AMERICAN MADE

Anvil with hole for use with KWM, K&D, and Drill-A-Bush tools.  Select from uses for CBT-60-1, 2 and 3, CBT-60-4, CBT-60-5, and CBT-60-6 reamers. Also available are AN-1 (4.32mm inside diameter) and AN-2 (4.29mm inside diameter).  Pieces...

BUSHING BOXES - TWO

A box designed to hold many sizes of bushings. Made of solid wood. Measures: 4 3/4" x 7 5/8" x 1". 60 holes in lid to help locate bushings. Two boxes included.  Bushings are not included.  Also available is Box-60 for one box.

HERSCHEDE BUSHING KIT BERGEON AMERICAN REAMERS

Herschede Bergeon bushing kit consists of: one BA-5 System Brass KWM size bushing assortment (100 bushings, 10 sizes at 10 each) one HRB-1 Herschede Back Plate Winding Arbor Bushings (10 bushings) one HFR-1 Herschede Front Plate Winding Arbor Bushings...

HERSCHEDE BUSHING KIT KWM AMERICAN REAMER

Herschede KWM bushing kit with American reamers consists:  and one CBT-60/6A KWM Reamer Size 8.68mm. Herschede KWM bushing kit consists of: one BA-5 System Brass KWM size bushing assortment (100 bushings, 10 sizes at 10 each) one HRB-1 Herschede...

AMERICAN BRASS KWM BUSHING ASSORTMENT #1

American made "The System" 100 brass bushing assortment. 10 of each size. For BA refills: Use American Made KWM Size Brass L + bushing number. For example: American Made KWM Size Brass L-14 when available. Otherwise use American Made Brass 5 digit number...

AMERICAN BRASS KWM BUSHING ASSORTMENT #5

American made "The System" 100 brass bushing assortment. 10 of each size. For BA refills: Use American Made KWM Size Brass L + bushing number. For example: American Made KWM Size Brass L-14 when available. Otherwise use American Made Brass 5 digit number...

BRASS BUSHING WIRE 12 PIECE ASSORTMENT SMALL SIZES

Brass wires are 3"L. Largest diameter wire .1380" (3.49mm) and smallest diameter wire .038" (.97mm). Assortment of 12 pieces total.  Smaller sizes than the BWA-12 assortment.

DRILL PRESS ADAPTER BERGEON

Adapter fits drill press for Bergeon bushings. Width: 3/8" or larger chuck. Size: 1 7/8"L. Includes a hex wrench for tightening.

AMERICAN BRASS SYSTEM BUSHINGS KWM SIZED

Best quality. Tooled with high precision. Fully finished and 35% harder than the foreign made bushings and others. Very durable and long lasting.  "The System" American Made Brass Bushings Interchange with KWM system. Select the available AMERICAN...

KWM BRASS GERMAN BUSHINGS L-XXX

Select the available KWM BRASS Bushing (L-part number) from the table below. NOTE:  L-28, -31, -50, -73, -78, -80, -81, -84, -118, -119, -120, -121, -123, -128, -129, -135, and L-137 are no longer made by Flume.  

CLAMP ON BUSHING TOOL - BERGEON STYLE

Clamp to clock plate after shaft is removed. Insert reamer into reamer holder and ream hole. Available for Bergeon reamers. Includes: 2 plate clamps, choice of spindle, Bergeon with set screw, and spindle upright support. Bergeon Style...

KWM STYLE REAMERS - AMERICAN MADE

Hand reamers for American and KWM bushings. Select from reamer sizes ranging from 1.18mm to 8.68mm, a chamfering tool, long or short centering points, or a handle. Centering point tools are used to located the pivot center prior to reaming. Pieces sold...

LARK AD-A-PIVOT

There is no drilling required to replace a clock pivot with this assortment of replacement pivots. Simply select the replacement pivot closest to your needs, dress down the shaft of the clock wheel, insert into the end of the Ad-A-Pivot, and dress down...

SCREW-IN BUSHING ACCESSORY - TAP

Tap accessory for Screw-In Bushing Tool SBT-245.

SCREW-IN BUSHING ACCESSORY - PLACING TOOL

Placing tool accessory for Screw-In Bushing Tool SBT-245.

SCREW-IN BUSHING ACCESSORY - CHAMFER

Chamfer accessory for Screw-In Bushing Tool SBT-245.  Length:  2 3/8"L.

SCREW-IN BUSHING ACCESSORY - CENTERING TOOL

Centering tool accessory for Screw-In Bushing Tool SBT-245. 2 1/2" long.

SCREW-IN BUSHING ASSORTMENT U.S.A

Screw-in bushing assortment with 8 different sizes in a plastic case. Bore sizes: 0.7mm, 0.8mm, 0.9mm, 1.0mm, 1.25mm, 1.5mm, 1.75mm, and 2.0mm, each at 1.8mm and 3.0mm height, for a total of 160 bushings.